manualshive.com logo in svg

Airaya AI108-4958-1, Manual And Installation Manual

Share
Download
Airaya AI108-4958-1 Manual And Installation Manual Download Page 51

 

- 51 - 

Airaya

 – Fast and affordable outdoor wireless bridges

 

 
 
 

 
If you receive ping responses from both test stations, the network IP configuration and 
physical wiring is working properly between the 2 test stations using Ethernet.  If you 
cannot ping both test stations, check your Ethernet cable connections and test station 
network settings to verify they are configured properly.    

 
 
 
  
 

When ping works properly with wired test stations, go to Step 2. 

 
 

Step 2. Setup wired Ethernet network connections to bridges

   

 

Connect directly using crossover cables, or through network switches or routers using 
straight-thru Ethernet cables.  
 

 

 

 
 
 
 
 

Example IP Configuration of test stations and outdoor bridges with default 
configuration parameters:

 

 

NOTE 

WirelessGRID products shipped as complete kits have one bridge factory-configured with IP address 192.168.1.70, and one 
bridge factory-configured with IP address 192.168.1.71

.  

Both bridges have a default subnet mask of 255.255.255.0 

100 Mbps full duplex ports are best from connecting bridges to wired Ethernet networks. 

NOTE 

If ping does not work between 2 wired test stations, it will not work between 2 test stations connected by a WirelessGRID link. 

Summary of Contents for AI108-4958-1





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands