Airaya AI108-4958-1 Manual And Installation Manual Download Page 47

Page: 47 / 60

- 47 -

Airaya

– Fast and affordable outdoor wireless bridges

LED Status

Indicators

Power, Radio Link/Activity, Network Link/Activity

Real-time

Monitoring

Secure Management Interface – Centralized real-time statistics

and signal strength monitor.

Indoor Bridge to Outdoor Antenna Cable

Cable Type

LMR-400

Cable Length

25 ft (7.62 meters). For other lengths, please contact AIRAYA

Cable Connectors

N-type Male to N-type Male

Interfaces

Antenna Connector N-Type Female Input

Bridge Connector

N-Type Female Input

Ethernet

100/10 Mbps Ethernet (RJ-45), 100 Mbps full-duplex
recommended

Electrical

Power Input

100-120V Auto-ranging (~50Hz-60Hz). 220V option available

Power Output

5VDC, 2Amps (2.1mm Coax, Center-pin positive)

Mechanical Dimensions

Outdoor Antenna

12 x 12 x 1 in (30 x 30 x 2.5 cm)

Wireless Bridge

7.6 x 5.5 x 1.2 in (19.4 x 14.0 x 3.05 cm)

Outdoor Antenna

Mount

Includes mast mount(s) and clamp kit(s) for 1 to 4.5 in (26 to 115

mm) diameter mast, also wall-mount capable

Environmental

Radio Operating

Temperature

32°F to 149°F, 0 to 55°C

Radio Operating

Humidity

Max 95% non-condensing

Outdoor Antenna

Outdoor antenna: Fully weather protected

Compliance and Certification

EMC

FCC Part 15, Industry Canada RSS-210, Mexico, ETSI

Safety

UL - Canada, USA, CE

Radio

Public Safety (Part 70 fixed wireless) FCC 15.407 (UNII, ISM),
Industry Canada RSS-210, ETSI (w/TPC and DFS)

Summary of Contents for AI108-4958-1





























































Search results

Summary of Contents for AI108-4958-1

Reviews:

Brands by name

Popular brands

Airaya AI108-4958-1, Manual And Installation Manual

Search results

Summary of Contents for AI108-4958-1

Reviews:

Brands by name

Popular brands