manualshive.com logo in svg

Airaya AI108-4958-1, Manual And Installation Manual

Share
Download
Airaya AI108-4958-1 Manual And Installation Manual Download Page 13

 

- 13 - 

Airaya

 – Fast and affordable outdoor wireless bridges

 

Hardware Installation 

 

Indoor Bridge Connections 

 
 
 
 

 

Figure 5. 

Front and 

rear panel views 

 

 
 

 
 
 
 
 

 
 

 

The AI108-4958-N, AI108-4958-1, or AI108-SU connect to your network with a 
standard 100/10 Mbps Ethernet cable; and connects to the outdoor antenna 

using an RF cable. The AI108-4958-N, -1, -SU units features the following LED 
status indicators: 

 
 

LED 

Indication 

Power LED 

Blinks while bridge is powering up and performing power-on 
self-test. While bridge is ready, LED remains on without 

blinking. 

5 GHz LED 

Indicates the bridge is operating in 4.9-5.85 GHz range. LED 

blinks at a different rate in correspondence to the transfer 

rate. 

2.4 GHz LED 

Indicates the bridge is operating in 2.4-2.5 GHz.  This 

functionality is not available in standard configuration. 

10M LED 

Indicates the bridge has a physical Ethernet connection and 

is linked to your network at 10 Mbps. 

100M LED 

Indicates the bridge has a physical Ethernet connection and 

is linked to your network at 100 Mbps. 

Rear Panel 

Reset button 

Pressing the reset button and holding it in for more than 4 

seconds will set the bridge network settings to factory 

defaults.  Cycle the power to enable new settings. 

 

 

Summary of Contents for AI108-4958-1





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands