background image

STEP 1)

Secure a primary air source of sufficient air flow and discharge pres

-

sure.  The number and type of respirators being used determines the 

flow rate and pressure required.

STEP 2)

Check airline monitor for fresh 9 volt batteries and turn unit on.  Connect 

the remote signal cable, 115 VAC plug, and air sample hose to the monitor.  

Place the “ON/OFF/TEST” switch to the “ON” position.  Allow 30 seconds 

for the readout to stabilize.  If a reading other than “00” is displayed, cali

-

bration of the monitor may be necessary. See calibration procedure.

Note: Remote signal cable does not apply to BB15 series.

STEP 3)

Connect the extension cord to a 115 VAC receptacle.  

Note: The CO monitor can run off the 9 volt batteries if AC  power is not 

available.

STEP 4)

Connect the optional remote alarm (DC only) assembly to the remote 

alarm jack. 

Note: This step does not apply to BB15 series.

STEP 5)

Close the flowmeter by turning the control knob fully clockwise. Do not 

over-tighten.

BREATHER BOX™ SETUP AND OPERATION

Note: Always operate the Breather Box™ in the upright positi on.  Failure to comply may result in one or all

           of the  following:

1) Auto drains will not functi on properly.  This may result in the contaminati on of the CO monitor and cause   

     oil/water to be passed through respirator hose and into the worker’s mask.

2) Auto drains may become clogged.

3) Filters may accumulate moisture and/or contaminati on.

8

Summary of Contents for BB100-CO






















Reviews: