manualshive.com logo in svg

Air Monitor VELTRON DPT-plus, Installation, Operation And Maintenance Manual

Share
Download
Air Monitor VELTRON DPT-plus Installation, Operation And Maintenance Manual Download Page 9

VELTRON DPT-

plus

Air Monitor Corporation

116-010-91.P65 (09/18/09)

VELTRON DPT-

plus

 - IO&M Manual

4

3.5 – ALARM (option)

The VELTRON DPT-

plus

 Alarm provides the means for having the process signal compared to user selectable alarm

points and automatically activates a Form A relay to generate dry contact alarm signal(s).  User selectable alarm
configurations of Low/High, Low1/Low2, and High1/High2 plus Alarms On/Off, Setpoints, Dead Bands, and Delays are
configurable via the User Setup menu.  Alarm Setpoints can be displayed during 

Normal

 operating mode.

One choice among three alarm types are available to the user: Low/High; Low1/Low2; or High1/High2.  An Alarm Delay
is available, if implemented (any time setting greater than zero), any condition that would normally cause an alarm,
triggers the delay timer first.  If the alarm condition still exists after the delay times out, then the appropriate alarm
relay(s) are activated.                will be displayed whenever any alarm relay is activated.  Alarm On/Off, Type, Setpoints,
Deadbands, and Delays are available and configurable using the User Setup menu.  The Alarm Setpoints can be
displayed during 

Normal

 operation.

High Alarm

Process Signal

High2 Alarm

Point

Point

Process Signal

Low1 Alarm

High1 Alarm

Point

Point

Low Alarm

Low2 Alarm

Process

Point

Point

Signal

Low/High Alarm

Low1/Low2 Alarm

High1/High2 Alarm

3.6 – DATA DISPLAY

The integral display is a multi-line, backlit graphical LCD capable of displaying three lines of operating data.  It can also
display a user settable I.D. number using any combination of standard ASCII characters.  It is also used by the User
Setup menu for displaying the menu parameters and values.  Configuring the display for 

Normal

 operation is done using

the User Setup menu.

3.7 – K-FACTOR

The VELTRON DPT-

plus

 is equipped with a K-factor feature which allows for the calculation and introduction of a bias

and/or gain factor into the transmitter's flow calculations.  The K-factor feature is intended to be used in two types of
applications:

1. To adjust for flow measurement error as a result of highly distorted airflow induced by upstream or downstream flow

disturbances.

2. To adjust the transmitter's output to bring it into close correlation with field measured flow data.

The K-Factor gain and bias values can be entered directly or the VELTRON DPT-

plus

 can calculate these values based

on measured and reference values from a 1, 2 or 3 point airflow traverse.

3.8 – FLOW/DIFFERENTIAL PRESSURE CALCULATOR

The VELTRON DPT-

plus

 is equipped with an integral calculator feature that allows the user to determine the maximum

flow or differential pressure from the appropriate variables.  This feature allows the user to determine input or output
values at various points of the process or new values if the process parameters have changed.  Also, the calculator can
be used to implement a single-point density compensation for operating temperature and/or absolute pressure.

SECTION 3 – FEATURES

alrm

Summary of Contents for VELTRON DPT-plus































































Reviews:

No comments

Brands by name

Popular brands

Load more brands