AGM RMSAL User Manual Download Page 24

24

AGM Global Vision

4   WARRANTY INFORMATION

4.1  WARRANTY INFORMATION

This product is guaranteed to be free from manufacturing defects in material and 

workmanship under normal use for a period of three (3) years from the date of 

purchase. In the event that a defect covered by the warranty below occurs during 

the applicable period stated above, AGM Global Vision, at its discretion, will either 

repair or replace the product; such action on the part of AGM Global Vision shall 

be the full extent of AGM Global Vision’s liability, and the Customer’s sole and 

exclusive reparation. This warranty does not cover a product if it has been (a) used 

in ways other than its normal and customary manner; (b) subjected to misuse; (c) 

subjected to alterations, modifications or repairs by the Customer or by any party 

other than AGM Global Vision without prior written consent of AGM Global Vision; 

(d) is the result of a special order or categorized as “close-out” merchandise or 

merchandise sold “as-is” by either AGM Global Vision or the AGM Global Vision 

dealer; or (e) merchandise that has been discontinued by the manufacturer and 

either parts or replacement units are not available due to reasons beyond the 

control of AGM Global Vision. AGM Global Vision shall not be responsible for 

any defects or damage that in AGM Global Vision’s view are a result from the 

mishandling, abuse, misuse, improper storage or improper operation of the device, 

including use in conjunction with equipment that is electrically or mechanically 

incompatible with, or of inferior quality to, the product, as well as failure to maintain 

the environmental conditions specified by the manufacturer. This warranty is 

extended only to the original purchaser. Any breach of this warranty shall be 

enforced unless the customer notifies AGM Global Vision at the address noted 

below within the applicable warranty period.
The customer understands and agrees that except for the foregoing warranty, 

no other warranties written or oral, statutory, expressed or implied, including any 

implied warranty of merchantability or fitness for a particular purpose, shall apply 
to the product. All such implied warranties are hereby and expressly disclaimed.

4.2 LIMITATION OF LIABILITY

AGM Global Vision will not be liable for any claims, actions, suits, proceedings, 

costs, expenses, damages, or liabilities arising out of the use of this product. 

Operation and use of the product are the sole responsibility of the Customer. AGM 

Global Vision’s sole undertaking is limited to providing the products and services 

outlined herein in accordance with the terms and conditions of this Agreement. 

The provision of products sold and services performed by AGM Global Vision to 

the Customer shall not be interpreted, construed, or regarded, either expressly or 

implied, as being for the benefit of or creating any obligation toward any third party 

of legal entity outside AGM Global Vision and the Customer; AGM Global Vision’s 

Summary of Contents for RMSAL





























Reviews: