Agilent Technologies N9010A Manual Download Page 22

Page: 22 / 107

Chapter 3

ACP Measurements

Configuring the Measurement System

The BTS under test must be set to transmit the RF power remotely
through the system controller. This transmitting signal is connected to
the RF input port of the analyzer. Connect the equipment as shown.

Figure 3-1

Adjacent Channel Power Measurement System

1. Using the appropriate cables, attenuator and adapters, connect the

output signal of the BTS to the RF input of the analyzer.

2. Connect a BNC cable between the frequency reference port of the

BTS and the EXT REF IN port of the analyzer.

3. Using a BNC cable, connect the trigger signal from the BTS to the

TRIGGER1 IN port of the analyzer.

4. Connect the system controller to the BTS through the serial bus

cable to control the BTS operation.

Summary of Contents for N9010A












































































































Search results

Summary of Contents for N9010A

Reviews:

Related manuals for N9010A

Brands by name

Popular brands

Agilent Technologies N9010A, Manual

Search results

Summary of Contents for N9010A

Reviews:

Related manuals for N9010A

Brands by name

Popular brands