Agilent Technologies N9010A Manual Download Page 90

Page: 90 / 107

Chapter 12

Monitor Spectrum Measurements

Configuring the Measurement System

The base station (BTS) under test have to be set to transmit the RF power remotely
through the system controller. This transmitting signal is connected to the analyzer
RF input port. Connect the equipment as shown.

Figure 12-1

Transmit Power Measurement System

1. Using the appropriate cables, adapters, and attenuator, connect the output

signal of the BTS to the RF input of the analyzer.

2. Connect a BNC cable between the frequency reference port of the BTS and the

EXT REF IN port of the analyzer.

3. Using a BNC cable, connect the trigger signal from the BTS to the TRIGGER1

IN port of the analyzer.

4. Connect the system controller to the BTS through the serial bus cable to control

the BTS operation.

Summary of Contents for N9010A












































































































Search results

Summary of Contents for N9010A

Reviews:

Related manuals for N9010A

Brands by name

Popular brands

Agilent Technologies N9010A, Manual

Search results

Summary of Contents for N9010A

Reviews:

Related manuals for N9010A

Brands by name

Popular brands