manualshive.com logo in svg

Agilent Technologies G1888, User Information

Share
Download
Agilent Technologies G1888 User Information Download Page 42

42

User Information

Introduction to Headspace and to the G1888 Network Headspace Sampler

Figure 12

 shows how the instrument synchronizes the 

availability of a vial which has been heated and is ready for 
injection with the GC’s readiness for another injection. For 
simplicity, the two cases are:

•

Situation A: total preparation time of 30 minutes with a run 
cycle time of 15 minutes.

•

Situation B: total preparation time of 15 minutes with a run 
cycle time of 30 minutes.

Figure 12

Instrument synchronization

Run 2

Run 3

Vial 1 prepared

Vial 2 prepared

Vial 3 prepared

Vial 4 prepared

Minutes

15

30

60

90

130

Run 1

A

B

Run 2

Run 3

Run 1

Vial 1

Vial 2

Vial 3

Vial 4

prepared

prepared

prepared

prepared

medium_standard.book  Page 42  Tuesday, February 17, 2004  10:14 AM

Summary of Contents for G1888

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands