background image

1 - 14

As -delivered state

The followings settings are active in the 

as-

delivered state

:

- The telephone system is set for

connection to a system port. You only
have to enter the system phone number.

- The switches S400 and S401 (termination

for the external S0 port) are closed, the
100 ohm termination resistors switched
on.

Analog ports - internal phone numbers
(decade 1 set) and terminal types

AS 31 ST

: 11 to 18,  telephones

AS 32

: 11 to 20,  telephones

- External access: unlimited for all users
- Line seizure: line seizure „0“
- Call variant 1 (day): on, no internal phone

number entered, subscribers 11, 12 and
13 are called in the case of a call

- Call variant 2 (night): off, no internal

phone number entered

- Call forwarding internal: off, no internal

phone number entered

- Number of calls: 5

- Don´t disturb: off for all terminals
- Knocking protection: off for terminals
- Transfer of phone numbers to the called

party and the caller: on

- Music on Hold (MoH): internal on

- Door call variant 1 (day): on, no internal

phone number entered, subscribers 11,
12 and 13 are called in the case of a door
call

- Door call variant 2 (night): off,no internal

phone number entered

- Automatic dialing: off

- Printout of connection data set: off for all

users

- Printout of dialed phone number: without

- Cost limit: no entry
- Own tariff units factor: 0,12 DM
- Base factor (network operator factor):

0, 12 DM

- Cleardown at cost limit: off
- Setup code: off
- Cost code: no entry
- Switch box code: no entry

- Least Cost Router (LCR): off, for all

subscribers

- Busy on busy: off
-

AS 32:

 Transfer of „0“ to dial from call list

at internal S0 port: off

System telephones ST 20 and ST 25 (AS 32)

- Status display: off
- Cost display: off
- Display: German
- Call list: off

Summary of Contents for AS 31 ST

















Reviews: