AEMC 203 User Manual Download Page 36

Page: 36 / 44

4.2.11 Adapter Function Measurement
4.2.11.1 In DC mode

Measurement Range (1)

0.0 to 599.9mV

0.60 to 5.999V

Specified Measurement Range (2)

0 to 100% of the measurement range

Accuracy

1% R ±3cts

Resolution

0.1mV

1mV

Input Impedance

10M

Ω

4.2.11.2 In AC mode

Measurement Range (1)

5.0 to 599.9mV

0.600 to 5.999V

Specified Measurement

Range (2)

1 to 100% of the

measurement range

0 to 100% of the

measurement range

Accuracy

5.0 to 59.9mV

± (1% R + 10cts)

60.0 to 599.9mV

± (1% R +3cts)

1% R ±3cts

Resolution

0.1mV

1mV

Input Impedance

10M

Ω

Note (1) The basic display is

000 counts. The position of the decimal count

and the display of multiples (m and k) depend on the programming of

the scale factor.

•

In DC, the display indicates "+OL" above +5999 counts and "-

OL" below -5999 counts. The "-" and "+" signs are managed

(polarity).

•

In AC, the display indicates "OL" above 5999 counts.

Note (2) - The max. bandwidth is 1kHz.

Specific specifications in MAX/MIN mode

(from 10Hz to 1kHz):

•

Accuracy: add 1% R to the values of the table above.

•

Capture of the extreme: approximately 100ms.

Summary of Contents for 203













































Search results

Summary of Contents for 203

Reviews:

Related manuals for 203

Brands by name

Popular brands

AEMC 203, User Manual

Search results

Summary of Contents for 203

Reviews:

Related manuals for 203

Brands by name

Popular brands