62
HA-266
TEST YOUR SYSTEM
Please make sure that the system is in DISARMED mode when you perform the tests.
(DEFAULT)
(when AC
or DC power is firstly connected)
STANDBY BATTERY TESTING ROUTINES
The system can be programmed to perform dynamically and automatically test of its standby
battery with the options of periodic test and manual test.
The test takes 2 minutes. The
LED will flash during the test.
AC power is turned OFF in order to monitor the battery under load during the test.
Two beeps will be generated and the
LED will be OFF if the battery is normal.
If the battery is low or dead, five beeps will be generated, the
LED will be ON. The
control console will continuously generate the warning signal of one short beep per 30
seconds until the next test.
A battery status report will be sent to the monitor station on the following two testing results
if the communicator is enabled:
1) The battery is
A battery
report.
2) The battery resumes
but it was
A battery
report.
No report will be given if the battery is normal in this test and it was also normal in the last
test.
1) The system will refuse to initiate the standby battery dynamic test in alarm condition, or, in
the condition of AC power failure, but the system will send a battery low report automatically
before battery exhausting if the battery is
lasting for more than two minutes.
2) The standby battery should be replaced every two to three years with a rechargeable 12V,
1.2Ah, lead acid battery.
The system can be programmed with the following options for periodic testing of the back-up
battery, please put a " " in the box showing your selected option:
OPTION
SELECTED
OPTION
SELECTED
OPTION
SELECTED
The counting of the periodic test starts at the time when the system is power-up
.
The time counting of the periodic test is not affected by the manual battery test.
!
!
!
!
!
!
!
BATTERY
BATTERY
BATTERY
LOW
LOW
NORMAL
LOW
NORMAL
NOTE:
LOW
TEST THE BACK-UP BATTERY -- PERIODIC
DAILY (EVERY 24 HOURS) BATTERY TEST ENABLED
WEEKLY (EVERY 7 DAYS) BATTERY TEST ENABLED
PERIODIC BATTERY TEST DISABLED
PROGRAMMING THE PANEL
You may program the panel from the system control console. Firstly, you are required to make
the system in programming mode, then key in the two digit
, followed immediately by the desired programming values
, then press
the [#] key to store the data. The console will beep twice to confirm the data is successfully
stored, and that 5 beeps will be generated for unsuccessful data entry. If you are not sure that
the correct programming values have been entered, program the programming location again.
After programming is finished, press the [ ] key twice to leave programming mode.
The maximum allowable time for each digit entry is 10 sec
For the owner's convenience in programming at the first time, the factory has put a Master Code
1234 into the system. The owner can use this code for the system to enter to programming mode.
To compromise security, in all cases, the owner should program a personal Master Code to
invalidate the factory set Master Code.
FACTORY SET
MASTER CODE
VALIDATION
The console will beep twice to confirm that the system is in programming mode.
The
LED is ON.
In the case that the factory set Master Code was replaced by your own Master Code, you have
to use your personal Master Code to enter to programming mode.
The console will beep twice to confirm that the system is in programming mode.
The
LED is ON.
Programming Location or the
address
(program data)
PROGRAM
PROGRAM
1. USE THE FACTORY SET MASTER CODE
2. USE YOUR OWN MASTER CODE
!
!
!
!
MASTER CODE
VALIDATION
onds.
1 2 3 4
ATTENTION:
Please make sure that the alarm control panel is firmly fixed to the metal box before
applying power to the system. Otherwise, the tamper switch will be triggered instantly to
give alarm and there will be no user code available for turning off the alarm before the
system is programmed.
HOW TO ENTER PROGRAMMING MODE
MASTER CODE
15
HA-266
