AEG PS?254?L, Original Instructions Manual

Page: 24 / 104

20
Deutsch
GB
Never use the mitre saw to cut materials other than those specified
in the instruction manual.
Long workpieces must be adequately supported.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
Do not point laser at reflective surfaces, Avoid exposure to laser
radiation. Laser may emit hazardous radiation.
Do not replace the installed laser with a different type.
Do not use this tool ‘s dust extraction as a vacuum cleaner to pick
up anything, such as hardness work pieces or nails etc. it will cause
the fan damage.
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium profiles, Non-
ferrous metals and plastics.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under “Technical Data” fulfills all the relevant regulations and the
directives 2011/65/EU (RoHs), 2004/108/ EC, 2006/42/EC and the
following harmonized standards have been used:
EN 61029-1:2009 + A11:2010
EN 61029-2-9:2009
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-11:2000
Winnenden, 2013-05-21
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
MAINS CONNECTION
Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
to sockets without an earthing contact as the design conforms to
safety class II.
MAINTENANCE
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Clean the tool and guarding system with clean cloths.
The ventilation slots of the machine must be kept clear at all times.
WARNING! Read all safety warnings and all instruc-
tions, including those given in the accompanying brochure.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Appliances used at many different locations including open air
should be connected via a residual current device (FI, RCD, PRCD) of
30mA or less.
Before doing any work on the machine, pull the plug out of the
socket.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
The handle lock must always be engaged when transporting the
mitre saw.
Ensure that the machine is always stable and secure (e.g. fixed to
a bench)
Keep the floor area free of loose material e.g. chips and cut-offs.
Before using the tool please read the instructions. If possible have
the tool demonstrated.
Always use the protective shields on the machine.
Only use the saw with guards in good working order and properly
maintained, and in position.
Do not clamp the protective swing guard.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the machine when it is running.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of
safety as soon as the faults are discovered.
Do not use any flanges other than those supplied or indicated in the
instruction manual to secure the saw blade.
Replace the table insert when worn
Do not use saw blades which are damaged or deformed
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Do not use saw blades made of high-speed steel.
Only use saw blades which have been properly sharpened. It is
essential to adhere to the maximum speed specified on the saw
blade.
Transport and store the tools in a suitable receptacle.
It is necessary to select a saw blade which is suitable for the
material being cut.
English