background image

Keep children away from the controller’s electronics and the battery compartment! 

All work must be carried out in accordance with national electrical regulations and the relevant local speciafications.  

1.2

 

Exemption from Liability 

We cannot accept liability for damage caused by disregarding these instructions within a radius of the controller even if this 
damage occurs due to malfunctioning of the controller caused by incorrect installation or programming. 
It is neither possible for the manufacturer to monitor compliance with these instructions nor the conditions prevailing and 
methods used during installation, operation, use and maintenance of the system controller. Incorrect execution of the 
installation may lead to material damage and to subsequent danger to people. The installer himself must be liable for such 
damage.  
We therefore accept no responsibility or liability for losses, damage or costs arising as a result of faulty installation; incorrect 
operation, improper use and maintenance or that is in any way connected thereto.  
Likewise we accept no responsibility for patent infringements or infringements of Third Party rights resulting from the use of 
this system controller. The manufacturer reserves the right to make modifications with regard to the product, technical data 
or assembly and operating instructions without prior notice.  
The user shall be responsible for use of the controller in areas of application not defined by the manufacturer  

Caution: opening the device up and operation contrary to the intended purpose lead to loss of warranty.  

1.3

 

Area of Use 

The system controller is used in photovoltaic power supplies with battery store for the hobby and leisure sector, residential, 
business and trade sectors as well as small businesses.  

1.4

 

Installation Instruction 

The controller is only suitable for use indoors protected against the effects of weather such as rain and solar 
radiation. 

The controller must be installed in the same room as the battery for the following reasons: 
A built-in temperature sensor detects the ambient temperature  

SLX Night Operating Instructions 

page 4 

 

Summary of Contents for PR 0606 Night



















Reviews: