Advantech SKY-8232D User Manual Download Page 88

Page: 88 / 133

SKY-8232D Manual V02 20220411

Page 88

password and must be entered to boot or enter Setup. In Setup the
User will have Administrator rights.

3. The password length must be in the following range:

Minimum length: 3

Maximum length: 20

3.2.6 Post & Boot Menu

Users can configure the system boot priority settings via the boot page. The default
setting of boot priority

of boot option #1 is “UEFI: Built-in EFI Shell”; Users can define the

boot priorities based on the application.

Figure 3-26: Post and Boot Menu

Table 3-18: Post & Boot Menu

Group

Setup Item

Access /

Options

Description

None

Setup Prompt
Timeout

Number of seconds to wait for
setup activation key.

Bootup NumLock
State

Select the keyboard NumLock
state.

Quiet Boot

Disabled

Enabled

Enables or disables Quiet Boot
option.

Network Stack

Disabled

Enabled

Enable/Disable UEFI Network
Stack

UEFI PXE Support

Disabled

Enabled

Enable/Disable IPv4 PXE boot
support. If disabled, IPv4 PXE
boot support will not be
available.

Redfish Support

Disabled

Enable/Disable Redfish

Summary of Contents for SKY-8232D
























































































































Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands

Advantech SKY-8232D, User Manual

Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands