Advantech SKY-8232D User Manual Download Page 65

Page: 65 / 133

SKY-8232D Manual V02 20220411

Page 65

Enabled

will reboot during restart in
order to change State of the
Device.

Pending TPM
Operation

None

TPM Clear

Choose TPM operation for next
boot.

Device Select

TPM1.2
TPM2.0

Auto

TPM 1.2 will restrict support to
TPM 1.2 devices, TPM 2.0 will
restrict support to TPM 2.0
devices, Auto will support both
with the default set to TPM 2.0
devices if not found, TPM 1.2
devices will be enumerated

Current
Status
Information

Firmware Version Display Only

Shows TPM FW version

Vendor

Display Only

Shows TPM vendor

TPM Enabled
Status

Display Only

Shows TPM Enablement Status

TPM Active
Status

Display Only

Shows TPM Activation Status

TPM Owner
Status

Display Only

Shows Current TPM Owner

3.2.2.4 Trusted Computing (if TPM2.0 present)

When system with TPM2.0 module installed, and the BIOS will auto detect it and the
related setting will be shown in the BIOS setup menu as below.

Figure 3-8: Platform Setup: Trusted Computing (TPM2.0)

Summary of Contents for SKY-8232D
























































































































Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands

Advantech SKY-8232D, User Manual

Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands