Advantech SKY-8232D User Manual Download Page 29

Page: 29 / 133

Page 29

2.3 Technical Specifications

2.3.1 SKY-8232D System Specification

Processor
System

CPU

Dual socket 3rd Generation Intel® Xeon® Scalable
Processor up to 185W TDP

Chipset

Intel® PCH C62xA series

Memory

Technology

Up to 32x 3200MHz DDR4 ECC Standard ECC
RDIMM/LRDIMM

Capacity

Max capacity per DIMM: 64GB
Max total capacity per system: 2048GB

Socket

32x 288-pin DIMM

PCIe

Expansion slot

1) 4x FH/FL PCIe x16 Gen4+ 2x LP 4.0 x8
2) Or 2x FH/FL PCIe 4.0 x16 slots + 2x FH/FL PCIe

4.0 x8 slots + 2x FH/HL PCIe 4.0 x8 slots+2x LP
4.0 x8

Front IO

1x 3.0 USB (the upper one) 1x 2.0 USB (the lower
one), VGA port, PWR, Status, ALARM LEDs

Rear IO

2 x GbE LAN RJ45, 1 x RJ45 Management port,1 x
VGA, 2 x USB3.0, 1 x Console port 1 x OCP3.0 (PCIe
Gen4 x16) module slot

Ethernet

Gigabit Ethernet
Interface

10/100/1000 Mbps

10 Gigabit Ethernet
Interface

Via OCP3.0 module

Controller

GbE LAN: Intel i210-AT support

Connector

2x RJ-45

Storage

Internal: 2 x 2.5" SATA SSD

Rear: 2 x 2.5" SATA SSD

Internal(on-board) : 2x M.2 2280 (SATA3)

Power
Supply

Power Rating

1200W AC PSU / 800W DC PSU

Input

(AC)

100-240VAC, 12-7A, 50-60Hz.

C) -40 - -60dc, 25.2-16.8A

Environment

Operational humidity 50% @25°C to 95%@40°C (non-condensing)
Non-operational
humidity

95% @60°C (non-condensing)

Operational
temperature

-5~55°C (23 ~ 131 °F) (Depends & by CPU SKU)

Storage temperature

-40 ~ 70°C (-40 ~ 158°F)

Cooling

Chassis Fan

6x hot pluggable (6056) fans (Hot swappable and N+1
redundant fan modules)

Thermal Control

Two separate thermal zones for motherboard and FL
PCIe cards

Reliability

Resilient to single fan failure

Summary of Contents for SKY-8232D
























































































































Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands

Advantech SKY-8232D, User Manual

Search results

Summary of Contents for SKY-8232D

Reviews:

Brands by name

Popular brands