background image

PCM-3618 User Manual

ii

Copyright

The documentation and the software included with this product are copyrighted 2008
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase. 
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:

1.

Collect all the information about the problem encountered. (For example, CPU 
speed, Advantech products used, other hardware and software used, etc.) Note 
anything abnormal and list any onscreen messages you get when the problem 
occurs.

2.

Call your dealer and describe the problem. Please have your manual, product, 
and any helpful information readily available.

3.

If your product is diagnosed as defective, obtain an RMA (return merchandize 
authorization) number from your dealer. This allows us to process your return 
more quickly.

4.

Carefully pack the defective product, a fully-completed Repair and Replacement 
Order Card and a photocopy proof of purchase date (such as your sales receipt) 
in a shippable container. A product returned without proof of the purchase date 
is not eligible for warranty service.

5.

Write the RMA number visibly on the outside of the package and ship it prepaid 
to your dealer.

Part no. 2000361801

Edition 2

Printed in Taiwan

April 2009

Summary of Contents for PCM-3618





























Reviews: