Advantech ITA-5831 Series User Manual Download Page 8

Page: 8 / 96

ITA-5831 User Manual

viii

Figure 3.5 Easy-Swap Module Installation (1)........................... 21
Figure 3.6 Easy-Swap Module Installation (2)........................... 22
Figure 3.7 COM Module (ITA-EM-SR61-001AE) ...................... 22
Figure 3.8 PoE Module (ITA-PE61-00A1E)............................... 23
Figure 3.9 CAN Module (ITA-CN61-00A1E).............................. 23
Figure 3.10Battery Module (ITA-BA61-00A1E) .......................... 24

3.5

RTC Battery Installation .......................................................................... 25

Figure 3.11RTC Battery Installation ........................................... 25

3.6

Antenna Installation ................................................................................ 26

Figure 3.12Antenna Installation.................................................. 26

Chapter

BIOS Settings

.................................... 27

4.1

Introduction ............................................................................................. 28

4.2

Entering the BIOS ................................................................................... 28

4.3

Main Setup.............................................................................................. 29

4.4

Advanced BIOS Setup ............................................................................ 30
4.4.1

Trusted Computing ..................................................................... 31

4.4.2

PCH-FW Configuration ............................................................... 32

4.4.3

Embedded Controller Configuration ........................................... 33

4.4.4

F81216 Controller Configuration................................................. 34

4.4.5

CPU Configuration...................................................................... 37

4.4.6

SATA Configuration .................................................................... 38

4.4.7

Network Stack Configuration ...................................................... 39

4.4.8

CSM Configuration ..................................................................... 41

4.4.9

USB Configuration ...................................................................... 42

4.4.10 PCIE COM Port Configuration .................................................... 43

4.5

Chipset Configuration ............................................................................. 44
4.5.1

System Agent Configuration ....................................................... 45

4.5.2

Graphics Configuration ............................................................... 46

4.5.3

LCD Control ................................................................................ 47

4.5.4

PEG Port Configuration .............................................................. 48

4.5.5

PCH-IO Configuration................................................................. 49

4.5.6

PCI Express Configuration ......................................................... 50

4.6

Security Configuration............................................................................. 51

4.7

Boot Configuration .................................................................................. 52

4.8

Save & Exit ............................................................................................. 53

Chapter

Driver Installation

.............................. 55

5.1

Introduction ............................................................................................. 56

5.2

Driver Installation .................................................................................... 56
5.2.1

Chipset Windows Driver Setup ................................................... 57

5.2.2

VGA Windows Driver Setup........................................................ 60

5.2.3

ME Windows Driver Setup.......................................................... 60

5.2.4

LAN Windows Driver Setup ........................................................ 61

5.2.5

USB 3.0 Windows Driver Setup.................................................. 61

5.2.6

Audio Windows Driver Setup ...................................................... 61

Chapter

GPIO Programming Guide

............... 63

6.1

Digital DI/O Definition.............................................................................. 64

6.2

Configuration Sequence ......................................................................... 64

Table 6.1: ICH SMBUS I/O Space ............................................ 64
Table 6.2: Pin Definitions .......................................................... 65

6.2.1

Command Byte ........................................................................... 65
Table 6.3: Command Byte......................................................... 65

6.2.2

PCA9554 Register 0 – Input Port Register ................................. 66

Summary of Contents for ITA-5831 Series

































































































Search results

Summary of Contents for ITA-5831 Series

Reviews:

Related manuals for ITA-5831 Series

Brands by name

Popular brands

Advantech ITA-5831 Series, User Manual

Search results

Summary of Contents for ITA-5831 Series

Reviews:

Related manuals for ITA-5831 Series

Brands by name

Popular brands