manualshive.com logo in svg

Advantech EKI-1526/N/I/TI, User Manual

Share
Download
Advantech EKI-1526/N/I/TI User Manual Download Page 6

EKI-1526(TI) | 1528(TI) User Manual

vi

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from

damage.

To avoid electrical shock, always disconnect the power from your PC chassis 

before you work on it. Don't touch any components on the CPU card or other 

cards while the PC is on.

Disconnect power before making any configuration changes. The sudden rush 

of power as you connect a jumper or install a card may damage sensitive 

electronic components.

Safety Precaution - Power Cord Safety

Please read the following safety information carefully before installing the switch:

The unit must be connected to an earthed (grounded) outlet to comply with 

international safety standards.

The unit must be powered by using listed power source, rated 12-48Vdc, 0.7A 

minimum and Tma 75°C comply with LPS or PS2.

Do not connect the unit to an A.C. outlet (power supply) without an earth 

(ground) connection.

The socket outlet must be near to the unit and easily accessible. You can only 

remove power from the unit by disconnecting the power cord from the outlet.

Précaution de Sécurité - Sécurité du Cordon 
d'Alimentation

Veuillez lire attentivement les informations de sécurité suivantes avant d'installer le

commutateur:

L'appareil doit être connecté à une prise de terre (mise à la terre) pour se 

conformer aux normes de sécurité internationales.

L'appareil doit être alimentée en utilisant une source d'alimentation répertoriée, 

nominale 12-48Vdc, 0,7A minimum et TMA 75°C conforme à LPS ou PS2.

Ne connectez pas l'appareil à une prise de courant alternatif CA (alimentation) 

sans une connexion à la terre.

La prise de courant doit être proche de l'appareil et facilement accessible. Vous 

ne pouvez couper l'alimentation de l'appareil qu'en débranchant le cordon 

d'alimentation dès la prise de courant.

Warning!

Installation and removal of the unit must be carried out by qualified 
personnel only.

Attention!

L'installation et le retrait de l'unité doivent être effectués uniquement 
par du personnel qualifié.

Summary of Contents for EKI-1526/N/I/TI












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands