manualshive.com logo in svg

Advantech EKI-1526/N/I/TI, User Manual

Share
Download
Advantech EKI-1526/N/I/TI User Manual Download Page 36

EKI-1526(TI) | 1528(TI) User Manual

22

Pour se connecter à une alimentation électrique:

1.

Éteignez toutes les sources d'alimentation et tous les équipements connectés à 

l'appareil.

2.

Fixez les câbles de signal au produit.

3.

Fixez le cordon d'alimentation à l'appareil.

–

Pour les l'appareils à base de CA, assurez-vous de vous connecter aux 

prises d'appareil.

–

Pour les l'appareils à base de CC:

Assurez-vous que la polarité est comprise entre 12 et 48 VCC

RTN est une connexion positive

 

12 à 48 VDC est une connexion négative

La mise à la terre doit être munie d'une cosse à deux trous pour la 

sécurité

4.

Fixez les câbles de signal aux appareils connectés.

5.

Connectez les cordons d'alimentation à la source.

6.

Allumez toutes les sources d'alimentation.

Pour se déconnecter d'une alimentation électrique:

1.

Éteignez toutes les sources d'alimentation et tous les équipements connectés à 

l'appareil.

–

Pour les l'appareils à base de CA: retirez tous les cordons d'alimentation de 

la prise d'alimentation du châssis ou interrompez l'alimentation du dispositif 

de distribution  d'alimentation CA.

–

Pour les l'appareils à base de CC: débranchez les sources d'alimentation CC 

du panneau de disjoncteur ou éteignez la source d'alimentation avant de 

déconnecter les câbles CC.

2.

Retirez les câbles de signal des connecteurs.

3.

Retirez tous les câbles de l'appareil.

Summary of Contents for EKI-1526/N/I/TI












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands