AWMT
25
6. UNPACKING AND INSTALLATION
This Section contains instructions for the site preparation, unpacking and the installation of the
AWMT transceiver.
6.1 INITIAL INSPECTION
Inspect the shipping container for damage resulting from the shipment. If damaged, immediately
contact the carrier that delivered the equipment and submit a damage report. Failure to do so
may invalidate future claims.
6.2 UNPACKING
Carefully remove all of the items from the shipping container. Save all of the packing material
until completing successfully the visual inspection. Verify that all of the items listed on the
packing list have been received. If any of the items are missing, contact ADVANTECH AMT
™
immediately. Inspect all of the items for evidence of damage resulting from the shipment. If
damage seems evident, immediately contact the carrier that delivered the equipment and file a
claim. Failure to do so may invalidate future claims. Check the AWMT thoroughly for damaged
or loose parts.
6.3 INSTALLATION
Installation of the AWMT requires the following phases:
Relay, Serial Interface and AC (or DC) Power interconnecting cable construction
Environmental and adequate ventilation considerations
Mechanical, RF and electrical installation
at page 21 lists all of the mounting connectors used by the AWMT unit and their
corresponding mating connectors.
at page 21 and in
at page 22 show the
location of the mounting connectors.
6.3.1 R
ELAY
, S
ERIAL
I
NTERFACES AND
AC (
OR
DC) P
OWER
C
ABLES
C
ONSTRUCTION
Prior to constructing the interconnecting cables, verify that the all of the cables are of sufficient
length in order to connect the AWMT unit to the user’s remote monitor and control system.
Construct the Relay, RS-232, RS-485 serial interfaces and AC (or DC) Power interconnecting
cables as follows:
Summary of Contents for AWMT
