![background image](http://html1.mh-extra.com/html/advantech/awmt/awmt_installation-and-operation-manual_2858636017.webp)
AWMT
16
4.3.4 P
OWER
A
MPLIFIER
M
ODULE
The
Power Amplifier Module
amplifies the RF signals arriving from the L/RF
up-converter module.
Temperature sensors are installed at the module’s hot spots to prevent the RF devices from
overheating and operating at temperatures exceeding 85ºC.
The power amplifier will be in the Mute mode if the user sends a MUTE command through the
Relay or serial interfaces.
The power amplifier will shut down if the hot spot temperature e85
°
C and any of the
GaAs FET devices fails.
4.3.5 W
AVEGUIDE
A
SSEMBLY
The
Waveguide Assembly
contains a forward and reflected power detector, an RF output
circulator and the harmonic filters.
The forward power and the reflected power detectors monitor the RF output power level and the
reflected power level respectively. The digital signals are sent to the Main Controller Board.
The circulator provides a VSWR protection at the RF output port. The termination load of the
isolator is capable of fully absorbing any reflected power.
4.3.6 L
OW
N
OISE
B
LOCK
(LNB)
The LNB functions as a low noise amplifier and a frequency down converter. The RF input
signals are shifted downwards into the L-Band frequency range. Following the conversion the
L-Band signals are amplified to a power level sufficient for transmission into the L-Band to IF
Down-Converter module.
4.3.7 10 MHz R
EFERENCE
O
SCILLATOR
This module is used to generate a highly stable and very low phase noise 10 MHz reference
frequency with a high stability (of
±
5 x 10
-8
MHz/year typical), which is required by all of the
converter modules and the LNB. A 10 MHz reference is sent to each converter module via a
coaxial cable. The oscillator requires approximately 10 minutes to warm up after the transceiver
is power up.
Summary of Contents for AWMT
