![background image](http://html1.mh-extra.com/html/advantech/awmt/awmt_installation-and-operation-manual_2858636036.webp)
AWMT
35
TABLE 9
: RS-232 MENU ITEM DEFINITION
Item
Description
S/N
AWMT serial number
Soft
Version number of the main controller software within the AWMT.
Unit Pos
Indicates the position of the unit A or B. (1:1 redundant system only).
Name
Indicates the name of the AWMT.
MAC
Indicates the serial address of the AWMT main controller (in hex).
Current
Indicates the 12 VDC current consumption of the AWMT, in amperes.
TxF
Indicates the transmission frequency of the AWMT in MHz.
TxF Shift
Indicates the local oscillator frequency of the transceiver transmission path in
MHz.
FPWR
Indicates the forward power of the transceiver (transmission path output
power) in dBm.
TxGain
Indicates the transmission Gain in dB.
Tx Stat
Indicates the transmission status (On or Mute).
RPWR
Indicates the reverse (reflected) power of the transceiver (the transmission
path reflected power) in dBm.
RxF
Indicates the receive frequency of the transceiver in MHz.
RxF Shift
Indicates the local oscillator frequency of the transceiver receive path in MHz.
Rx Level
Indicates the receive path output power level (not available for the unit).
RxGain
Indicates the receive gain in dB
Rx Stat
Indicates the receive status (On or Mute)
LNx Curr
Indicates the current consumption of the Low Noise Block Down Converter
(LNB) in amperes.
Temp HS
Hot spot temperature of the unit in degrees Celsius.
PS
Power Supply DC Voltage
Elaps Time
Elapsed Time from the first start-up of the unit (days:hours)
Alarms
Provides the alarm and fault messages and the normal status message:
1. Alarm (12 VDC current, faulty RF devices, power supply failure,
IF-L or L-RF up-converter modules failure, L-IF down-converter module
failure, low power alarm, high power alarm).
2. Temperature Pre-Alarm (hot spot temperature exceeds 75 ºC)
3. Out of Lock of the PLL in IF-L or L-RF up-converter modules, or in L-IF
down-converter module triggering a shutdown
4. High Reflected Power shutdown
5. Overdrive Alarm (output power exceeds by 1.5 dB the rated P1dB)
6. Temperature shutdown (hot spot temperature exceeds 85ºC)
7. OK (AWMT transceiver is functioning properly).
Ref
Reference (internal or external)
Summary of Contents for AWMT
