AWMT
15
4.3.1 IF
TO
L-B
AND
U
P
-C
ONVERTER
M
ODULE
The
IF/L-Band Up-Converter Module
converts and amplifies the incoming IF carrier into
L-Band carrier.
Incorporated into the module is an attenuator with a 20-dB adjustable range. The attenuator is
used to adjust transmit (Tx) gain of the AWMT.
The synthesiser within the module contains an out of lock protection circuitry that prevents the
L-Band carrier from shifting in frequency. When the oscillator is not phase-locked with the
10 MHz reference, an Alarm signal is sent to the main controller board and the up-converter
module will mute automatically.
The operating frequency for the synthesiser and the attenuation are externally controlled by a
serial signal from the main controller board. The transmitting frequency is adjustable in
1 MHz steps.
4.3.2 L-B
AND TO
RF U
P
-C
ONVERTER
M
ODULE
The
L/RF Up-Converter Module
converts and amplifies the incoming L-Band carrier into the
desired RF-Band carrier.
The synthesiser within the module contains an out of lock protection circuitry that prevents the
L-Band carrier from shifting in frequency. When the oscillator is not phase-locked with the
10 MHz reference, an Alarm signal is sent to the main controller board and the up-converter
module will mute automatically.
4.3.3 L-B
AND TO
IF D
OWN
-C
ONVERTER
M
ODULE
The
L/IF-Band Down-Converter Module
converts and amplifies the incoming RF signals into
the desired IF frequency range.
Similarly as for the up-converter modules, a 10 MHz high stability reference signal is used to
phase-lock an internal synthesiser.
The operating frequency for the synthesiser and the input attenuation are externally controlled in
the same manner as for the IF/L-Band Up-converter module. The receive (Rx) frequency is
adjustable in 1 MHz steps.
The out of lock protection circuitry within the synthesiser functions similarly as for the
IF/L-Band Up-Converter Module.
The L/IF module pr12 VDC and the 10 MHz reference to the LNB
Summary of Contents for AWMT
