![background image](http://html1.mh-extra.com/html/advantech/acp-2000/acp-2000_user-manual_2856530003.webp)
iii
ACP-2000 User Manual
/ 用户手册 / 用戶手冊
Safety Instructions
/安全指示
1.
Read these safety instructions carefully.
2.
Retain this user manual for future reference.
3.
Disconnect the equipment from all power outlets before cleaning. Use only a
damp cloth for cleaning. Do not use liquid or spray detergents.
4.
For pluggable equipment, the power outlet socket must be located near the
equipment and easily accessible.
5.
Protect the equipment from humidity.
6.
Place the equipment on a reliable surface during installation. Dropping or letting
the equipment fall may cause damage.
7.
Do not leave this equipment in an environments where the storage temperature
is under 0 °C (32 °F) or above 40 °C (122 °F), as it may damage the equipment.
8.
The openings on the enclosure are for air convection. Protect the equipment
from overheating. Do not cover the openings.
9.
Ensure that the voltage of the power source is correct before connecting the
equipment to a power outlet.
10.
Position the power cord away from high-traffic areas. Do not place anything over
the power cord.
11.
All cautions and warnings on the equipment should be noted.
12.
If the equipment is not used for a long time, disconnect it from the power source
to avoid damage from transient overvoltage.
13.
Never pour liquid into an opening. This may cause fire or electrical shock.
14.
Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
15.
If any of the following occurs, have the equipment checked by service person
-
nel:
The power cord or plug is damaged.
Liquid has penetrated the equipment.
The equipment has been exposed to moisture.
The equipment is malfunctioning, or does not operate according to the user
manual.
The equipment has been dropped and damaged.
The equipment shows obvious signs of breakage.
16.
The computer is provided with a battery-powered real-time clock circuit. There is
a danger of explosion if battery is incorrectly replaced. Replace only with same
or equivalent type recommended by the manufacture. Discard used batteries
according to the manufacturer’s instructions.
(1) Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of
Used Batteries According to the Instructions.
(2) Risque d'explosion si la batterie est remplacée par un type incorrect. Mettre
au rebus les batteries usagées selon les instructions.
17.
THE COMPUTER IS PROVIDED WITH CD DRIVES (or Laser Products).They
comply with the appropriate safety standards: IEC 60825-1 or EN 60825-1.
(1) Avoid direct exposure to the laser beam. Do not open the laser device enclo
-
sure. There are no user serviceable components inside.
(2) Do not operate controls, make adjustments, or perform procedures to the
laser device other than those specified herein.
(3) Allow only authorized service technicians to repair the laser device.
Summary of Contents for ACP-2000
