Advancing Alternatives Aegis Tec User Manual Download Page 19

Page: 19 / 20

SYSTEM SETTINGS

Fan Settings

Description

Default

Min

Max

P89

Start temperature for Fan#1

60°

1°

99°

P90

Start temperature for Fan#2

66°

1°

99°

P95

Fan #1 DIF1 start temperature

60°

1°

99°

P96

Fan#2 DIF1 start temperature

75°

1°

99°

P101

Fan #1’s DIF2 start temperature

70°

1°

99°

P102

Fan #2’s DIF2 start temperature

71°

1°

99°

P107

Fan temperature gap. Difference between on and off

0.5

P111

Fan #1 Max humidty. If humidity sensor is installed, when

fan #1 will start to dry out the building

99%RH

P112

Fan humidty hysteresis – set to 101% to disable humidity

function

101%

P113

Fan humidity temperature limit

32°

The temperature parameters control the starting temperature.
The fans are used for cooling. They will turn on above the temperature setpoint.
If humidity is connected , fan # 1 can be set to clear out the high humidity.

Summary of Contents for Aegis Tec





















Search results

Summary of Contents for Aegis Tec

Reviews:

Related manuals for Aegis Tec

Brands by name

Popular brands

Advancing Alternatives Aegis Tec, User Manual

Search results

Summary of Contents for Aegis Tec

Reviews:

Related manuals for Aegis Tec

Brands by name

Popular brands