Advancing Alternatives Aegis Tec User Manual Download Page 11 | Manualshive

Page: 11 / 20

background image

11

INSTALLATION

Locating the Rain Sensor

Connecting the Rain Sensor

Keep the sensor wire away from high voltage wire by at least 1 foot.
The rain sensor detects water droplets on the lens. Mount the sensor for rain detection relative to
the structure for the desired sensitivity.

Match the rain sensor wire, by color, to the corresponding terminal.

«
...
9
10
11
12
13
...
»

Summary of Contents for Aegis Tec





















Reviews:

No comments

Related manuals for Aegis Tec

Brand: Galcon Pages: 32

Brand: IBM Pages: 12

Brand: K&K Pages: 10

Brand: Gate Motors Pages: 6

Brand: Samson Pages: 78

Brand: Taco Electronic Solutions Pages: 28

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: WABCO Pages: 4

Brand: Rayrun Pages: 4

Brand: Parker Pages: 29

Brand: ZKTeco Pages: 43

HydroTap G5 Touch-Free Wave

Brand: Zip Pages: 24

Brand: Jetter Pages: 24

UNDER CONTROL CP-30A PILOT

Brand: G-Force Pages: 2

Clip Studio TABMATE

Brand: CELSYS Pages: 2

MIMIC HRNDWHEELS

Brand: MRMC Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands