background image

 

 

www.advancedco.com 

12 

2.3.2.2  Disables 

  [Disable List] 

Zone 1      DISABLED 

Man Release DISABLED 
  
 
 
 

If there are disablement conditions present, the display will show 
the number of conditions and a list of the disablements. 

Press the 



 buttons to scroll through the list of disablements. 

Press the 

 button to return to the previous menu. 

Disable conditions can only be set on the control panel. 

2.3.2.3  Warnings 

[Warning Status] 
       1 of 2 

VALVE MONITOR INPUT

.

 

>VALVE CLOSED      

.  

PRESSURE MONITOR 
>LOW PRESSURE 
 

If there are warning conditions in the extinguishant system present, 
the display will show the number of conditions and a list of the 
warning conditions. 

Press the 



 buttons to scroll through the list of warnings. 

Press the 

 button to return to the previous menu. 

 

2.3.2.4  Software Versions 

The display shows the revision of software installed in this RSI. The software revisions of the control panel and 
all RSI units can be viewed simultaneously on the panel. 

[Software Versions] 
RSI-6 : 02.00 
 
 
 
 
 

On selection, the display shows a list containing the panel and any 
configured remote status indicators along with the version of 
software installed in each device. 

Press the 



 buttons to scroll through the list of entries. 

Press the 

 button to return to the previous menu. 

2.3.3 

LED Test 

On selection, the front panel LED Indicators will be illuminated for a short period of time.  

2.3.4 

Exit 

On selection, the display reverts to the normal status display indications. 

 

Summary of Contents for ExGo Series





















Reviews: