Advanced Technology Video NVR16P Instruction Manual Download Page 100

Page: 100 / 125

100

9.1.3. Device

You can configure the peripherals in your NVR such as PTZ control and printer

9.1.3.1. Sensor Detection

Select the right type of your external sensors
connected to the NVR. There are two different
types of sensors, (N.O. - Normal Open and N.C. -
Normal Close). Press APPLY button to change
and select the sensor type.

** For detailed information, please refer to the
Main Menu under Device

9.1.3.2. Video Loss Detection

Video Loss Detection: Select ON or OFF for each
channel.

** For detailed information, please refer to the
Main Menu under Device

9.1.3.3. Alarm Schedule

You can set the conditions and operating hours
for scheduled alarms.

** For detailed information, please refer to the
Main Menu under Device

Summary of Contents for NVR16P






























































































































Search results

Summary of Contents for NVR16P

Reviews:

Related manuals for NVR16P

Brands by name

Popular brands

Advanced Technology Video NVR16P, Instruction Manual

Search results

Summary of Contents for NVR16P

Reviews:

Related manuals for NVR16P

Brands by name

Popular brands