ADT Entrepreneur 3000EN, Programming Manual

Page: 6 / 32

–
6
–
✱
60 TROUBLE REPORT CODE
| [10] Any non-zero entry in first digit enables report. ††
✱ 61 BYPASS REPORT CODE
| [00] Any non-zero entry in first digit enables report. †
✱
62
AC LOSS REPORT CODE
| [00] Any non-zero entry in first digit enables report. ††
✱
63 LOW BAT REPORT CODE
| [10] Any non-zero entry in first digit enables report. ††
✱ 64 TEST REPORT CODE
| [10] Any non-zero entry in first digit enables report. ††
Use Scheduling mode (event 11) or the key commands
listed
Periodic Test Report Scheduling Commands: below to set periodic test reports. Each command sets
installer code + [#] + [0] + 0 = report every 24 hrs schedule 32 to the stated repeat option; first test report
installer code + [#] + [0] + 1 = report once per week sent 12 hours after command.
installer code + [#] + [0] + 2 = report every 28 days
NOTE:
Make sure the Real-Time Clock is set to the proper
time before entering the test report schedule command to
ensure that test reports are sent when expected.
✱ 65 OPEN REPORT CODE
[0,0,0] Any non-zero entry enables report for partition. †
Part. 1 Part. 2 Common
✱
66
ARM AWAY/STAY RPT CODE
[0,0,0,0,0,0] Any non-zero entry
Away Stay ( Part. 1) Away Stay ( Part. 2) Away Stay ( Common)
enables report
NOTE:
“OPEN” reports are not sent if the associated closing report is not enabled.
UL:
† Required for UL commercial burglar alarm installations. †† Required for UL commercial burglar alarm and residential fire alarm
installations. ††† Required for residential fire alarm installations. †††† Must be enabled if wireless devices are used.
✱ 67 RF XMTR LOW BAT REPORT CODE
| [10] Any non-zero entry in first digit enables report. ††††
✱
68
CANCEL REPORT CODE
| [10] SIA NOTE: Report enabled.
✱
69 RECENT CLOSING REPORT CODE
| [11] SIA NOTE: Always enabled. Sends both recent closing and zone
Also see field *59. alarm reports if fault occurs within 2 min. after exit time expires.
✱ 70 ALARM RESTORE RPT CODE
[1] Any non-zero entry enables report. ††
✱
71 TROUBLE RESTORE RPT CODE
| [10] Any non-zero entry in first digit enables report.†††
✱ 72 BYPASS RESTORE RPT CODE
| [00] Any non-zero entry in first digit enables report.†
✱
73
AC RESTORE RPT CODE
| [00] Any non-zero entry in first digit enables report.††
✱
74 LOW BAT RESTORE RPT CODE
| [10] Any non-zero entry in first digit enables report.††
✱ 75 RF XMTR LO BAT RST RPT CODE
| [10] Any non-zero entry in first digit enables report. ††††
✱
76
TEST RESTORE RPT CODE
| [10] Any non-zero entry in first digit enables report.††
OUTPUT AND SYSTEM SETUP (
✱
✱ ✱
✱
77 –
✱
✱ ✱
✱
93)
✱
77 DAYLIGHT SAVINGS TIME
START\END MONTH
| [3][11]
0 = disabled
1-12 = month (1 = January, 2 = February, etc)
#+10 = October; #+11 = November; #+12 = December
✱
78 DAYLIGHT SAVINGS TIME
START\END WEEKEND
| [2][1]
0 = disabled, 1 = first, 2 = second, 3 = third
4 = fourth, 5 = last, 6 = next to last, 7 = third to last
∗
79, *80, *81, *82 MENU MODES
These are Menu Mode commands, not data fields, for Output Device Mapping, Output
Programming, Zone List Programming, and Alpha Programming respectively. See
page 2 and their respective sections in the Installation and Setup Guide for procedures.
✱
84 AUTO STAY ARM
[3]
0 = no, 1 = partition 1 only
2 = partition 2 only, 3 = both partitions
✱ 85 CROSS ZONE TIMER
This option not for use in UL installations.
NOTE : Cross zones take effect only after exit delay
expires.
[0]
(assign cross zones on zone
list 4, with *81 Menu mode)
0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min
1 = 30 seconds 7 = 3 min #+13 = 10 min
2 = 45 seconds 8 = 4 min #+14 = 12 min
3 = 60 seconds 9 = 5 min #+15 = 15 min
4 = 90 seconds #+10 = 6 min
5 = 2 minutes #+11 = 7 min
✱
86
CANCEL VERIFY DISPLAY
[1]
0 = no, 1 = yes
✱
89
EVENT LOG FULL REPORT CODE
| [00]
Enter any digit (other than "0") in the first box, to enable
report (entries in the second box are ignored)
✱
90
EVENT LOG ENABLES
NOTE :
System messages are logged when
any non-zero selection is made.
[15]
Example: To select
“Alarm/Alarm Restore”, and
“Open/Close”, enter 9 (1 + 8);
To select all, enter #15.
0 = None
1 = Alarm/Alarm Restore
2 = Trouble/Trouble Restore
4 = Bypass/Bypass Restore
8 = Open/Close