Adrian Olson ODOM Assembly Manual Download | Manualshive

Page: 7 / 23

background image

STEP 3

Assemble Keelson Block (continued)

STEP 4

Forward and Aft Bulkheads

Fit the Forward Bulkhead into the notch in the Keelson.
Glue in place.

Fit the Aft Bulkhead onto the back of the Keelson.
It should snap on tightly. Glue in place.

Slide the Keelson Upper Block onto the tubes. The tubes should protrude above the top 1/16”. Bond the Keelson Block
together with CA Glue or PVC cement.

1/16”

Page 7

Section View

STEP 5

Keelson Top and Braces

Use CA Glue to install the Keelson Top as shown.
The bottom side has holes to fit over the brass tubes.

The Braces fit in the grooves in the Aft Bulkhead
and against the sides of the Keelson Top.

© 2010 by Adrian Olson. All rights reserved.

«
...
5
6
7
8
9
...
»

Summary of Contents for ODOM
























Reviews:

No comments

Related manuals for ODOM

Brand: Radio Shack Pages: 4

Brand: GAME OF BRICKS Pages: 36

Brand: RC4WD Pages: 79

Brand: Amewi Pages: 11

Brand: Pinolino Pages: 12

Brand: le-idea Pages: 2

Brand: LEGO Pages: 176

Spring Rocking Horse

Brand: QABA Pages: 3

Megaphone Mission Voice Changer

Brand: VTech Pages: 12

Brand: Tabletop Scenics Pages: 12

Thunderbolt Mini A10

Brand: J-Power Pages: 31

Brand: Walkera Pages: 2

Brand: Radica Games Pages: 2

Batman Power Wing Laptop

Brand: Oregon Scientific Pages: 24

Mod Block Trolley

Brand: Mocka Pages: 2

Brand: Fisher-Price Pages: 2

Brand: Pichler Pages: 9

Brand: Vollmer Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands