manualshive.com logo in svg

ADLINK Technology ReadyBoard 910, Reference Manual, Page: 46 / 64

Share
Download
ADLINK Technology ReadyBoard 910 Reference Manual Download Page 46

Chapter 4

BIOS Setup

40

Reference Manual

ReadyBoard 910

9. Use the <Enter> key to select the screen menus listed in the Opening BIOS screen.

OEM Logo Screen (Splash) 

The ReadyBoard 910 BIOS supports a graphical logo screen, which can be customized by the user and an 
ADLINK Sales Representative and displayed when enabled through the BIOS Setup Utility. The graphical 

image can be a company logo or any custom image the user wants to display during the boot process.  

Logo Image Requirements

Please contact your ADLINK Sales Representative for more information on OEM Logo Screen 
requirements.

NOTE

The serial console port is not hardware protected. Diagnostic software that 
probes hardware addresses may cause a loss or failure of the serial console 
functions.

NOTE

The Quiet Boot feature must be set to Enabled in the Boot settings of BIOS 
Setup for the system to recognize the OEM Logo Screen.

Summary of Contents for ReadyBoard 910

































































Reviews:

No comments