manualshive.com logo in svg

ADLINK Technology ReadyBoard 910, Reference Manual

Share
Download
ADLINK Technology ReadyBoard 910 Reference Manual Download Page 45

ReadyBoard 910

Reference Manual

39

Chapter 4

BIOS Setup

Introduction

This section assumes the user is familiar with general BIOS Setup. Refer to the appropriate PC reference 

manuals for information about the on-board ROM-BIOS software interface. If ADLINK has added to or 
modified the standard functions, these functions will be described.

Entering BIOS Setup (Local Video Display)

To access BIOS Setup using a local video display for the ReadyBoard 910: 

1. Turn on the display and the power supply to the ReadyBoard 910.

2. Start Setup by pressing the [Del] key when the following message appears on the boot screen. 

Press DEL to run Setup

3. Follow the instructions on the right side of the screen to navigate through the selections and modify any 

settings.

Entering BIOS Setup (Serial Port Console) 

This section describes how to enable the Remote Access in VGA mode and enter the BIOS setup through a 

serial terminal or PC.   

1. Turn on the power supply to the ReadyBoard 910 and enter the BIOS Setup Utility in VGA mode.

2. Set the BIOS feature 

Serial Port Console

 to [Enable] under the 

Advanced

 menu.

3. Accept the default options or make your own selections for the balance of the Remote Access fields and 

record your settings.

4. Ensure you select the type of remote serial terminal you will be using and record your selection.

5. Select 

Save Changes and Exit

 and then shut down the ReadyBoard 910.

6. Connect the remote serial terminal (or the PC with communications software) to the COM port you 

selected and recorded earlier in the BIOS Setup Utility.

7. Turn on the remote serial terminal or PC and set it to the settings you selected in the BIOS Setup Utility.

The default settings for the ReadyBoard 910 are:

♦

ANSI 

♦

115200

♦

8 bits

♦

1 stop bit

♦

no parity

♦

no flow control

♦

VT-UTF8 Combo Key Support [Enabled]

♦

Recorder Modes [Disabled]

♦

Resolution 100x31 [Disabled]

♦

Legacy OS Redirection Resolution [80x24]

8. Restore power to the ReadyBoard 910 and press the F4 key after you see the following screen prompt.

Press <space bar> to update BIOS 

Summary of Contents for ReadyBoard 910

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands