ADLINK Technology ReadyBoard 910 Page 38 Reference Manual Download | Manualshive

Page: 38 / 64

background image

Chapter 3

Hardware

32

Reference Manual

ReadyBoard 910

Temperature Monitoring

The Super I/O controller performs the temperature monitoring function. The board temperatures can be
monitored from the Hardware Monitor feature in the Advanced BIOS setup screen.

User GPIO Signals

The ReadyBoard 910 provides eight GPIO pins for custom use. The signals are routed to the CN13 header,

and the enable and initialize values are set in the BIOS.

For more information about GPIO pin operation, refer to the Programming Manual for the Super I/O
controller at:

http://www.smsc.com/main/catalog/sch311x.html

describes the pin signals of the GPIO interface, which provides a 10-pin header of two rows with

odd/even (1,2) pin sequence and 0.079" (2mm) pitch.

Oops! Jumper (BIOS Recovery)

The Oops! jumper is provided in the event the BIOS settings you have selected prevent you from booting the

system. By using the Oops! jumper you can prevent the current BIOS settings in Flash from being loaded,
forcing the BIOS to use the default settings. Connect the DTR pin to the RI pin on Serial port 1 (COM0)

prior to boot up to prevent the present BIOS settings from loading. After booting with the Oops! jumper in

place, remove the Oops! jumper and go into BIOS Setup. Change the desired BIOS settings, or select the
default settings, and save changes before rebooting the system.

To convert a standard DB9 connector to an Oops! jumper, short together the DTR (4) and RI (9) pins on the

serial port DB9 connector at Serial Port 1, as shown in

.

Figure 3-2. Oops! Jumper Connection

NOTE

The ReadyBoard 910 requires an active heatsink (with fan) for the CPU and a
passive heatsink (without fan) for the PCH.

Table 3-13. User GPIO Signals Pin/Signal Descriptions (CN13)

Pin #

Signal

Description

1

GPI0

User defined

2

GPO0

User defined

3

GPI1

User defined

4

GPO1

User defined

5

GPI2

User defined

6

GPO2

User defined

7

GPI3

User defined

8

GPO3

User defined

9

NC

Not Connected

10

NC

Not Connected

Serial 2 Port

(CN8, COM1)

1

2

3

4

5

6

7

8

9

10

Top View

Or

RB910Oopsjumper

5

4

3

2

1

9

8

7

6

Standard DB9

Serial Port 1

(CN17, COM0)

Connector (Male)

Front View

«
...
36
37
38
39
40
...
»

Summary of Contents for ReadyBoard 910

































































Reviews:

No comments

Related manuals for ReadyBoard 910

Virtex-II Pro ML300

Brand: Xilinx Pages: 17

Brand: MaxLinear Pages: 25

MT9J003I12STCVH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: WinFast Pages: 75

Brand: JETWAY Pages: 40

Brand: ASROCK Pages: 144

Brand: Texas Instruments Pages: 7

Brand: Gigabyte Pages: 19

Brand: ECS Pages: 60

Brand: SOLTEK Pages: 94

Brand: ASROCK Pages: 61

DS320PR412-421EVM

Brand: Texas Instruments Pages: 31

Brand: Linear Technology Pages: 10

PHANTOM GAMING B650E PG-ITX WiFi

Brand: ASROCK Pages: 62

Brand: Hochiki Pages: 8

Brand: DFI Pages: 102

Brand: DFI Pages: 98

Brand: DFI Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands