ADLINK Technology ReadyBoard 910 Reference Manual Download Page 12

Page: 12 / 64

Chapter 2

Product Overview

Reference Manual

ReadyBoard 910

♦

Support RS232 capability on both ports

♦

Support full modem capability on both ports

♦

Support RS485 or RS422 operation on both ports

♦

Support programmable word length, stop bits, and parity

♦

Support 16-bit programmable baud-rate generator and an interrupt generator

•

Keyboard/Mouse Interface

♦

Provides PS/2 keyboard interface (shared with mouse)

♦

Provides PS/2 mouse interface (shared with keyboard)

♦

Provides shared over-current fuse

♦

Provides four dedicated open-drain ouputs

•

Audio Interface (HDA)

♦

Provides detection for up to four jacks

♦

Supports stereo low voltage (1.5V~3.3V) I/O

♦

Supports stereo digital microphone input

♦

Provides S/PDIF digital audio interface

•

Ethernet Interface

♦

Includes two fully independent RJ45 Gigabit Ethernet ports

♦

Integrated LEDs on each port (Link/Activity and Speed)

♦

Provides two Intel 8257IT controller chips

♦

Supports IEEE 802.3 10BaseT/100BaseTX and 10/100/1000BaseT compatible physical layer

♦

Supports Auto-negotiation for speed, duplex mode, and flow control

♦

Supports full duplex or half-duplex mode

•

Full-duplex mode supports transmit and receive frames simultaneously

•

Supports IEEE 802.3x Flow control in full duplex mode

•

Half-duplex mode supports enhanced proprietary collision reduction mode

•

Video Interfaces (VGA/DVI/LVDS)

♦

Support an integrated graphics controller

♦

Support analog a VGA DAC interface

♦

Support VGA resolutions up to 2048x1536 with 32-bit color at 75Hz

♦

Support DVI outputs (allow capacity to bring out TMDS signals to a DVI connector)

♦

Support DVI resolutions up to 1920x1200 at 60Hz

♦

Support LVDS 24bpp outputs (1 or 2 channel, four differential signals: 3-bits + clock)

♦

Support LVDS resolutions up to 1920x1080 at 60Hz

•

Miscellaneous

♦

Provides real-time clock (RTC) with replaceable battery

♦

Supports battery-free boot

♦

Provides external battery connection for RTC operation

♦

Provides user GPIO interface header

♦

Provides thermal and voltage monitoring

Summary of Contents for ReadyBoard 910

































































Search results

Summary of Contents for ReadyBoard 910

Reviews:

Brands by name

Popular brands

ADLINK Technology ReadyBoard 910, Reference Manual

Search results

Summary of Contents for ReadyBoard 910

Reviews:

Brands by name

Popular brands