ADLINK Technology ReadyBoard 910 Page 53 Reference Manual Download

Page: 53 / 64

Chapter 4

BIOS Setup

ReadyBoard 910

Reference Manual

♦

LCD Control

•

Primary IGFX Boot Display [

CRT

; DVI; LVDS]

•

Secondary IGFX Boot Display [

Disabled

; CRT; DVI; LVDS]

•

DDI function choose [

DisplayPort

; HDMI]

•

LCD Panel Type [640x480; 800x600;

1024x768

; 1280x1024; 1600x1200; 1920x1200;

1920x1080]

•

Active LFP [No LVDS;

Int-LVDS

]

•

Panel Scaling [

Auto

; Off; Force Scaling]

•

Panel Color Depth [

18 Bit

; 24 Bit]

♦

Memory Information

•

Memory RC Version X.X.X.X

•

Memory Frequency XXXX Mhz

•

Total Memory XXXX MB (DDR3)

•

DIMM#0 XXXX MB (DDR3)

•

DIMM#1 Not Present

•

CAS Latency (tCL) X

•

Minimum delay time

-CAS to RAS (tRCDmin)                    X
-Row Precharge (tRRmin)                  X
-Active to Precharge (tRASmin)       XX

•

PCH-IO Configuration

♦

Intel PCH RC Version X.X.X.X

♦

Intel PCH SKU Name HM65

♦

Intel PCH Rev ID XX/XX

♦

Azalia [Enabled; Disabled;

Auto

]

♦

82574L LAN Controller 1 [Disabled;

Enabled

]

♦

82574L LAN Controller 2 [Disabled;

Enabled

]

♦

USB 3.0 Controller [Disabled;

Enabled

]

♦

Restore AC Power Loss [Power Off;

Power On

; Last State]

♦

DC I2C Speed Control [

100khz

; 200khz; 400khz]

♦

USB Configuration

•

EHCI [

Disabled

; Enabled]

•

USB Ports Per-Port Disable Control [

Disabled

; Enabled]

Summary of Contents for ReadyBoard 910

































































Search results

Summary of Contents for ReadyBoard 910

Reviews:

Related manuals for ReadyBoard 910

Brands by name

Popular brands

ADLINK Technology ReadyBoard 910, Reference Manual

Search results

Summary of Contents for ReadyBoard 910

Reviews:

Related manuals for ReadyBoard 910

Brands by name

Popular brands