manualshive.com logo in svg

ADLINK Technology NeuronBot, User Manual, Page: 46 / 77

Share
Download
ADLINK Technology NeuronBot User Manual Download Page 46

 

 

 
46 

Operating Instructions 

 

 

•

  Session 2: 

6. Go back to the 

teleop_twist_keyboard session

. Press

 

x

 and 

c

 to decrease the linear speed to 0.3 m/s the 

angular speed to 0.2 rad/s, and then drive the NeuronBot around using the keyboard driver. After mapping 
the environment, remember to save the map 

before

 closing gmapping.

 

•

  Session 4: 

7. Source the environment. 

source /opt/ros/<YOUR_ROS1_DISTRO>/setup.bash 

source ~/neuronbot2_ros1_ws/devel/setup.bash 

roscd neuronbot2_nav/maps/ 

8. Save the map

.

  

A map file and a config file will be saved to 

neuronbot2_nav/maps

. 

rosrun map_server map_saver -f map_name 

9. Stop gmapping by pressing 

ctrl + c

 in the gmapping session (Session 3). 

5.3.3.  Navigation 

After getting a static map, running a SLAM package is not recommended due to its computational load. This 
section describes how to use an AMCL package to locate the NeuronBot using a previously generated map and 
existing laser scan. This will allow you to move the NeuronBot from one location to a specified destination. 

Note:

 Ensure that everything in the base driver has been launched before running SLAM. 

 

Terminal 1, 

Session 3:

 

1. Source the environment. 

source /opt/ros/<YOUR_ROS1_DISTRO>/setup.bash 

source ~/neuronbot2_ros1_ws/devel/setup.bash 

2. Start the navigation procedure by executing the following command. 

roslaunch neuronbot2_nav bringup.launch map:=map_name 

 

RViz: 

3. Click the 

Add

 button in the lower left.

 

 

Summary of Contents for NeuronBot














































































Reviews:

No comments