ADLINK Technology LittleBoard 735 Reference Manual Download

Page: 8 / 54

Chapter 1

About This Manual

Reference Manual

LittleBoard 735

Chip specifications

used on the LittleBoard 735:

•

Intel Corporation and the Atom N270 processor used for the embedded CPU.

Web site:

http://download.intel.com/design/processor/datashts/320032.pdf

•

Intel Corporation and the 82945GSE and 82801GBM chips, used for the Memory Hub/Video controller
and I/O Hub, respectively.

Web site:

http://download.intel.com/design/processor/datashts/309219.pdf

= Memory Hub

Web site:

http://www.intel.com/Assets/PDF/datasheet/307013.pdf

= I/O Hub

•

Intel Corporation and the 82562GT and 82574IT chips, used for the Fast Ethernet and Gigabit Ethernet
controllers, respectively.

Web site:

http://download.intel.com/design/network/datashts/82562gt.pdf

= Ethernet

Web site:

http://download.intel.com/design/network/datashts/82574.pdf

= Gigabit Ethernet

•

Standard Microsystems Corp and the SCH3114I-NU chip, used for the Super I/O controller.

Web site:

http://www.smsc.com/main/catalog/sch311x.html

•

Realtek and the ALC203 chip, used for the Audio CODEC.

Web site:

http://www.realtek.com.tw/search/default.aspx?keyword=ALC203

•

ITE Tech. Inc. and the IT8888F chip, used for the PCI-to-ISA bridge conversion.

Web site:

http://www.ite.com.tw/EN/products_more.aspx?CategoryID=3&ID=5,76

NOTE

If you are unable to locate the datasheets using the links provided, go to the
manufacturer’s web site where you should be able to perform a search using the
chip datasheet number or name listed, including the extension, htm, pdf, etc.

Summary of Contents for LittleBoard 735























































Search results

Summary of Contents for LittleBoard 735

Reviews:

Related manuals for LittleBoard 735

Brands by name

Popular brands

ADLINK Technology LittleBoard 735, Reference Manual

Search results

Summary of Contents for LittleBoard 735

Reviews:

Related manuals for LittleBoard 735

Brands by name

Popular brands