ADLINK Technology LittleBoard 735 Reference Manual Download | Manualshive

Page: 35 / 54

background image

Chapter 3

Hardware

LittleBoard 735

Reference Manual

29

USB Interfaces

The I/O Hub (82801GBM) provides the USB solution for both legacy UHCI controller and EHCI controller

(USB 2.0) support. The I/O Hub (Southbridge) contains port-routing logic that determines which controller
(UHCI or EHCI) handles the USB data signals. The J44 header provides two of the six USB ports: USB0

and USB1. The J14 header provides USB2 and USB3, and the J39 header provides USB4 and USB5.

USB 2.0 Support

The I/O Hub (Southbridge) contains an Enhanced Host Controller Interface (EHCI) compliant host

controller, which supports up to six high-speed USB 2.0 Specification compliant root ports. The higher
speed USB 2.0 specification allows data transfers up to 480 Mbps using the same pins as the six full-speed/

low-speed USB UHCI ports. The I/O Hub (Southbridge) port-routing logic determines which of the

controllers (UHCI or the EHCI) processes the USB signals.The USB 2.0 features implemented in the USB
ports include the following:

•

One EHCI host controller for all six USB ports

•

Supports USB V2.0 Specification

Legacy USB Support

The I/O Hub (Southbridge) supports three USB Universal Host Controller Interfaces (UHCI) and each Host

Controller includes a root hub with two separate USB ports each, for a total of six USB ports. The USB

Legacy features implemented in the USB ports include the following:

•

Three root hubs for six USB ports

•

Support for USB v1.1 and UHCI v1.1 with integrated physical layer transceivers

•

Improved arbitration latency for UHCI controllers

•

UHCI controllers support Analog Front End (AFE) embedded cell instead of USB I/O buffers to allow
for USB high-speed signaling rates

•

Three shared over-current fuses, located on the board, are used on all six USB ports

USB0 and USB1

Table 3-10

lists the USB0 and USB1 pin signals which use 10 pins, 2 rows, odd/even sequence (1, 2) with

0.079" (2mm) pitch.

CAUTION

ADLINK does not recommend connecting a USB boot device to the
LittleBoard 735 through an external hub. Instead, connect the USB boot
device directly to the LittleBoard 735.

Table 3-10. USB 0 & 1 Interface Pin Signals (J44)

Pin #

Signal

Description

1

USBPWR0

+5 volts power, USB 0

2

USBPWR1

+5 volts power, USB 1

3

USB0-

USB 0 Data Negative

4

USB1-

USB 1 Data Negative

5

USB0+

USB 0 Data Positive

6

USB1+

USB 1 Data Positive

7

USB GND0

USB 0 Ground

8

USB GND1

USB 1 Ground

«
...
33
34
35
36
37
...
»

Summary of Contents for LittleBoard 735























































Reviews:

No comments

Related manuals for LittleBoard 735

Brand: MSI Pages: 19

MBD-J-JNC9VL-H81

Brand: JETWAY Pages: 43

Brand: Norco Pages: 78

Venus VNS563-4GD

Brand: Diamond Systems Pages: 43

Brand: Texas Instruments Pages: 21

Brand: Telit Wireless Solutions Pages: 47

Coccinella Master Plus

Brand: SEA Pages: 2

Brand: Embedian Pages: 70

Brand: Gigabyte Pages: 64

Brand: Infineon Pages: 14

Brand: Gigabyte Pages: 44

Brand: MiTAC Pages: 132

Brand: Avalue Technology Pages: 92

Brand: NXP Semiconductors Pages: 7

Brand: DFI Pages: 85

RouterBOARD 500r5 Series

Brand: MikroTik Pages: 14

Brand: Toyama Pages: 48

Brand: Gan Systems Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands