ADLINK Technology LittleBoard 735 Reference Manual Download

Page: 12 / 54

Chapter 2

Product Overview

Reference Manual

LittleBoard 735

♦

Supports over-current detection status

•

Keyboard/Mouse Interface

♦

Provides PS/2 keyboard interface

♦

Provides PS/2 mouse interface

•

Audio interface

♦

Provides AC’97 CODEC on board

♦

Supports AC’97 standard

•

Ethernet Interface

♦

Provides two fully independent Ethernet ports

♦

Provides integrated LEDs on each port (Link/Activity and Speed)

♦

Provides Intel 82562GT and 82574IT controller chips

♦

Supports IEEE 802.3 10/100BaseT and 10/100/1000BaseT compatible physical layers

♦

Supports Auto-negotiation for speed, duplex mode, and flow control

♦

Supports full duplex or half-duplex mode

•

Full-duplex mode supports transmit and receive frames simultaneously

•

Supports IEEE 802.3x Flow control in full duplex mode

•

Half-duplex mode supports enhanced proprietary collision reduction mode

•

Video Interfaces (CRT/LVDS/TV Out)

♦

Support CRT (2048 x 1536) with up to 64MB UMA (Unified Memory Architecture)

♦

AGP 4X equivalent graphics performance

♦

Dual channel 9-, 12-, or 18-bit LVDS

♦

LVDS outputs (1 or 2 channel, four differential signals: 3-bits + clock)

♦

Provide one TV Out header

•

Miscellaneous

♦

Real-time clock (RTC) with replaceable battery

♦

Battery-free boot (Boots even if battery is dead or missing)

♦

Supports both on-board or external battery for Real Time Clock operation

♦

Thermal and Voltage monitoring

♦

Oops! Jumper (BIOS recovery) support

♦

Serial Console

♦

Watchdog timer (WDT)

Summary of Contents for LittleBoard 735























































Search results

Summary of Contents for LittleBoard 735

Reviews:

Related manuals for LittleBoard 735

Brands by name

Popular brands

ADLINK Technology LittleBoard 735, Reference Manual

Search results

Summary of Contents for LittleBoard 735

Reviews:

Related manuals for LittleBoard 735

Brands by name

Popular brands