ADLINK Technology HSL-4XMO User Manual Download Page 70 | Manualshive

Page: 70 / 112

background image

60

Operation Theory

The in-position function can be enabled or disabled, and the input
logic polarity is also programmable by the “inp_logic” parameter of
HSL_M_set_inp(). The INP signal status can be monitored by
software with the function: HSL_M_get_io_status().

X

Relative Functions:

HSL_M_set_inp()
HSL_M_get_io_status()
HSL_M_motion_done()

ALM

The processing of the ALM signal is a hardware build-in proce-
dure, and it is designed to interact with the alarm signal of the ser-
vomotor driver.

The ALM signal is an output signal from servomotor driver. Usu-
ally, it is designated to indicate when something is wrong with the
driver or motor.

The ALM pin receives the alarm signal output from the servo
driver. The signal immediately stops the HSL-4XMO from generat-
ing any further pulses or stops it after deceleration. If the ALM sig-
nal is in the ON status at the start of an operation, the HSL-4XMO
will generate the INT signal and thus not generate any command
pulses. The ALM signal may be a pulse signal with a minimum
time width of 5 microseconds.

Setting the parameters “alm_logic” and “alm_mode” of the
HSL_M_set_alm function can alter the input logic of the ALM.
Whether or not the HSL-4XMO is generating pulses, the ALM sig-
nal allows the generation of the INT signal. The ALM status can
be monitored by using the software function:
HSL_M_get_io_status().

X

Relative Functions:

HSL_M_set_alm()
HSL_M_get_io_status()

ERC

The ERC signal is an output from the HSL-4XMO. The processing
of the ERC signal is a hardware build-in procedure, and it is

«
...
68
69
70
71
72
...
»

Summary of Contents for HSL-4XMO

















































































































Reviews:

No comments

Related manuals for HSL-4XMO

Brand: Hansen Pages: 4

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: Olsberg Pages: 68

Brand: Tylo Pages: 51

Ambience Control 1

Brand: EuroLite Pages: 20

Brand: SKF Pages: 88

Brand: Pfeiffer Vacuum Pages: 100

Brand: We Pages: 27

Brand: Bartec Pages: 52

Brand: TAC Vista Pages: 2

4PP065.0571-B00

Brand: B&R Pages: 29

Brand: Ellard Pages: 21

Brand: WAGO Pages: 44

GTM TIM Capture 1

Brand: Infineon Pages: 13

Brand: C-TEC Pages: 42

Brand: Satel Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands