manualshive.com logo in svg

ADC ADView 2 9005BPSTO, User Manual, Page: 50 / 51

Share
Download
ADC ADView 2 9005BPSTO User Manual Download Page 50

     ADView 2 User Manual | 50 

93-9005-00 rev 4 

 

September 1, 2016

Limited Warranty 

ADC. provides to the original purchaser the following limited warranty from date of invoice. 

Main unit, SpO

2

 modules, temp modules 

3 years 

Blood Pressure Cuffs 

2 years 

Desktop Caddy, Wall Mount, Mobile Stand 

2 years 

Accessories (SpO

2

 sensors, temp probes, etc.) 

90 days 

ADC warrants each instrument to be free from defects in material and workmanship. Liability under this warranty 
covers servicing of the instrument when returned from the customer’s facility within the United States prepaid to the 
factory. ADC will repair any component(s) or part(s) that it finds to be defective during the period of this limited 
warranty. Should a defect become apparent, the original purchaser should first notify ADC of the suspected defect. 
The device should be carefully packaged and shipped prepaid to: 

American Diagnostic Corporation 

55 Commerce Drive 

Hauppauge, NY 11788 

Tel: 

1.800.ADC.2670 

1.631.273.9600 

Fax: 

1.631.273.9659 

The device will be repaired in the shortest possible time and returned prepaid by the same shipping method as 
received by the factory. This limited warranty is void if the device has been damaged by accident, misuse, negligence, 
or act of God, or serviced by any person not authorized by ADC. This limited warranty contains the entire obligation of 
ADC and no other warranties expressed, implied, or statutory are given. No representative or employee of ADC is 
authorized to assume any further liability or grant any further warranties except as herein.

Summary of Contents for ADView 2 9005BPSTO




















































Reviews:

No comments