manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Share
Download
ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 35

6.4.4 Cleaning the Lens

To clean the prism, perform the following procedure:

1. Clean the outer surface of the lens using liquid glass cleaner.

If the prism is coated with a substance impervious to the cleaner, apply a suitable solvent sparingly with a wad of cotton

or a patch of cloth.

2. After the solvent has acted, remove the softened coating with a clean piece of cotton or cloth.
3. Dry the prism with gently, dry, oil-free compressed air at a pressure no greater than 10 psi (0.69 bar) to evaporate or

remove all remaining cleaner.

6.4.5 Testing a LED Assembly

For this test, use a Fluke 87 or equivalent meter.

CAUTION

Do no use the megger function or a resistive test of any meter on an LED assembly! This may damage the LED’s

properties required for proper operation.

A “Diode Test” function may be used as a quick pass/fail check on an LED. In the maintenance shop, open the fixture and

unplug the LED assembly.

1. Set the meter to test a DIODE.
2. Connect the meter leads to the LED assembly.

Observe if the LED glow and also note the meter reading of the LED.

3. Then reverse the meter leads and observe the LED again.

UM-5073, Rev. 1.0, 2021/07/13

25

Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Summary of Contents for RELIANCE Omni 1-Dome



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands