manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Installation Manual, Page: 7 / 100

Share
Download
Adaptec 2100S - SCSI RAID Controller Installation Manual Download Page 7

vii

Contents

Installing the Driver for a Boot Controller in a New 

NetWare 4.2 Server 3-21

Installing the Driver in an Existing NetWare 4.2 

Server

3-23

Installing the Driver for a Boot Controller in a New 

NetWare 5 Server 3-24

Installing the Driver in an Existing NetWare 5 

Server

3-25

SCO UNIX 3-26

Installing the Driver in a New OpenDesktop 3.x 

System 3-26

Installing the Driver in a New OpenServer 5.0x 

System 3-27

Adding the Controller to an Existing OpenDesktop 3.x 

or OpenServer 5.x System 3-27

Adding the Controller to an Existing UnixWare 7 

System 3-28

FreeBSD 3-29
Linux 3-30

Installing the Driver in a New Linux System 3-30
Installing the Driver in an Existing Linux System 3-32

4

Installing Storage Management Software 

System Requirements 4-2
Installing Storage Manager Pro 4-2

Operating System Compatibility 4-2
Installation Prerequisites 4-3
Windows 4-3
NetWare 4.11 and 4.2 4-4
NetWare 5.x

4-6

Red Hat Linux and FreeBSD 4-7

Installing Storage Manager 4-8

Operating System Compatibility 4-8
Windows 4-8
NetWare 4-9
SCO UNIX 4-10
SCO UnixWare 7 4-10
FreeBSD 4-10
Linux 4-11

Summary of Contents for 2100S - SCSI RAID Controller





































































































Reviews:

No comments