manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Installation Manual, Page: 22 / 100

Share
Download
Adaptec 2100S - SCSI RAID Controller Installation Manual Download Page 22

1-14

Adaptec RAID Installation Guide

has not yet been incorporated into Storage Manager Pro. Keep 
in mind however, that the advantage of Storage Manager Pro 
over Storage Manager is its newer GUI, and its consistent look 
and feel across operating systems and between client and 
server platforms (due to it’s Java-based architecture). You can 
use either tool as the primary RAID management utility. For 
details, refer to the 

Adaptec Storage Management Software User’s 

Guide

.

■

RAIDUTIL Command Line Utility

—Provides the same 

functions as Storage Manager (or Storage Manager Pro) in 
environments where a GUI is not available. It is also scriptable, 
making it an invaluable companion RAID configuration utility 
in environments where many similarly-configured RAID 
subsystems must be replicated quickly. For details, refer to the 

Adaptec Storage Management Software User’s Guide

.

■

Storage Manager On ROM (SMOR)

—A built-in utility that is 

part of the controller’s BIOS code. You can start SMOR by 
pressing Ctrl+A during BIOS startup. For details, refer to 

Using 

SMOR

 on page 2-10

.

Summary of Contents for 2100S - SCSI RAID Controller





































































































Reviews:

No comments