manualshive.com logo in svg

Adaptec 2100S - SCSI RAID Controller, Installation Manual, Page: 65 / 100

Share
Download
Adaptec 2100S - SCSI RAID Controller Installation Manual Download Page 65

3-30

Adaptec RAID Installation Guide

Linux

The Adaptec RAID controller supports Red Hat 6.2 and 7.0 and SuSE 6.4 
and 7.0 with kernel versions 2.2.14-5.0, 2.2.16-22, 2.2.14, and 2.2.16.

Note: 

For the most up-to-date information on Adaptec’s 

support of Linux, or to download driver sources, visit 

http://linux.adaptec.com

.

Installing the Driver in a New Linux System

In this scenario, you are installing the controller in a new Red Hat 
Linux system. 

Note: 

This installation procedure applies to Red Hat 

Linux only.

To install the driver

1

Create the driver disk using the 

Adaptec RAID Installation CD

.

a

Insert the 

Adaptec RAID Installation CD

.

b

Boot from the CD. The CD loads a Linux kernel that is used 
to manage all of the CD functions.

c

Follow instructions and respond to prompts as necessary to 
get to the Adaptec splash screen.

d

When you see the Adaptec splash screen, click 

Create 

Driver Disk

. Then, click the appropriate operating system.

e

Insert a floppy disk and click 

OK

. The system creates the 

driver disk.

f

Remove the 

Adaptec RAID Installation CD

 and the driver 

floppy disk.

Summary of Contents for 2100S - SCSI RAID Controller





































































































Reviews:

No comments