background image

©Adam Equipment Co. 2019 

28 

WEEE 2012/19/EU 

This device may not be disposed of in domestic waste. This also applies to countries outside the 

EU, per their specific requirements. Disposal of batteries (if fitted) must conform to local laws 

and restrictions. 

Cet appareil ne peut être éliminé avec les déchets ménagers. L’élimination de la batterie doit 

être effectuée conformément aux lois et restrictions locales. 

Dieses Gerät nicht mit dem Hausmüll entsorgt. 

Dispositivo no puede ser desechado junto con los residuos domésticos 

Dispositivo non può essere smaltito nei rifiuti domestici. 

FCC / IC CLASS A DIGITAL DEVICE EMC VERIFICATION STATEMENT

 

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to Part 15 of the FCC rules and Canadian ICES‐003/NMB‐003 regulation. These 

limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  when  the 

equipment is operated in a commercial environment.  This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instruction 

manual,  may  cause  harmful  interference  to  radio  communications.    Operation  of this 

equipment in  a  residential  area is  likely to  cause  harmful  interference  in  which  case  the  user 

will be required to correct the interference at his own expense. 

CALIFORNIA PROPOSITION 65 - MANDATORY STATEMENT 

WARNING: This product includes a sealed lead‐acid battery which contains chemicals known to 

the State of California to cause cancer and birth defects or other reproductive harm. 

Adam  Equipment  products  have  been  tested  with,  and  are  always  supplied 

with  mains  power  adaptors  which  meet  all  legal  requirements  for  the 

intended  country  or  region  of  operation,  including  electrical  safety, 

interference  and  energy efficiency.  As  we  often  update  adaptor  products  to 

meet changing legislation it is not possible to refer to the exact model in this 

manual. Please contact us if you need specifications or safety information for 

your  particular item. Do  not  attempt to  connect  or use an  adaptor  not 

supplied by us. 

Summary of Contents for AGF 600aM

































Reviews: