Adam Equipment GK Page 17 User Manual Download

Page: 17 / 66

15 © Adam Equipment Company 2011

11.

OPERATION

11.1.

ZEROING

•

You can press the

[Zero]

key at any time to set the zero point from

which all other weighing and counting is measured. This will usually be

necessary when the platform is empty. When the zero point is obtained

the display will show the zero indicator.

•

The indicator has an automatic re-zeroing function to account for minor

drifting or accumulation of material on a connected platform. However

you may need to press

[Zero]

to re-zero the indicator if small amount of

weight is still shown when the platform is empty.

11.2.

TARING

11.2.1

MANUAL TARE

•

Zero the indicator by pressing

[Zero]

. The zero indicator will be on.

Place a container on the pan and its weight will be displayed.

•

Press

[Tare]

when the reading is stable. The weight that was displayed

is stored as the tare value and it is subtracted from the display, leaving

zero on the display. The stable and Net indicator will be on.

•

As a product is added only the weight of the product will be shown. The

indicator could be tared a second time if another type of product was to

be added to the first one. Again only the weight that is added after

taring will be displayed.

Summary of Contents for GK



































































Search results

Summary of Contents for GK

Reviews:

Related manuals for GK

Brands by name

Popular brands

Adam Equipment GK, User Manual

Search results

Summary of Contents for GK

Reviews:

Related manuals for GK

Brands by name

Popular brands