Adam Equipment GK User Manual Download

Page: 9 / 66

© Adam Equipment Company 2011

INSTALLATION

3.1.

UNPACKING

This indicator must be connected to a load cell platform and calibrated as necessary
to match the platform and user requirements. See Section 15 for set-up
information.

The users application and the technical specifications of the platform or load cell will
determine the necessary configuration.

LOCATING

•

The scales should not be placed in a location that will

reduce the accuracy.

•

Avoid extremes of temperature. Do not place in direct

sunlight or near air conditioning vents.

•

Avoid unsuitable tables. The table or floor must be rigid

and not vibrate.

•

Avoid unstable power sources. Do not use near large

users of electricity such as welding equipment or large

motors.

•

Do not place near vibrating machinery.

•

Avoid high humidity that might cause condensation.

Avoid direct contact with water. Do not spray or

immerse the scales in water.

•

Avoid air movement such as from fans or opening doors.

Do not place near open windows or air-conditioning

vents.

•

Keep the scales clean. Do not stack material on the

scales when they are not in use.

Summary of Contents for GK



































































Search results

Summary of Contents for GK

Reviews:

Related manuals for GK

Brands by name

Popular brands

Adam Equipment GK, User Manual

Search results

Summary of Contents for GK

Reviews:

Related manuals for GK

Brands by name

Popular brands